CTX Computer Monitor PR711FL User Manual

PR711FL User’s Manual  
U s e r ’ s M a n u a l  
P R 7 1 1 F L  
1
 
PR711FL User’s Manual  
Safety Instructions  
FCC Statement  
This equipment has been tested to comply with the limits for a class B digital device, pursuant  
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment generates, uses and can  
radiate radio frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
Relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which  
the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Warning:  
If a shielded-type power cord is supplied with this monitor, it is required in order to meet FCC  
emission limits and to prevent interference with nearby radio and television reception. Only  
shielded cables should be used to connect I/O devices to this equipment. You are cautioned  
that changes or modifications not expressly approved by the party responsible for compliance  
could void your authority to operate the equipment.  
CE Statement  
This device complies with the requirements of EMC (Electromagnetic Compatibility), and with  
Low Voltage directive.  
Safety Precautions  
Always observe these important safety instructions:  
1. Allow adequate ventilation around the monitor so that heat can be dissipated properly. Do  
not block or cover ventilated openings. Do not place the monitor in an enclosure that will  
obstruct the free flow of air.  
3
 
PR711FL User’s Manual  
2. Do not place the monitor or other heavy objects on the power cord. A damaged power cord  
can cause fires or electrical shock.  
3. Keep the monitor away from high-capacity transformers, electric motors and other strong  
magnetic fields.  
4. Do not connect to any voltage or frequency beyond the range specified on the back of the  
monitor. Please follow all warnings and instructions marked on the product.  
5. Unplug the monitor from the electrical power source before cleaning any part of the monitor.  
Do not use liquids, sprays or aerosol cleaners. Clean the surface of the screen with a lint-free,  
non-abrasive cloth and a non-alcohol, neutral and non-abrasive cleaning solution or glass  
cleaner. Use a slightly dampened cloth to clean the exterior of the plastic cabinet.  
6. This product is equipped with a 3-wire grounding-type plug, an important safety feature. This  
plug will only fit into a grounding-type power outlet. If a grounding-type power outlet is not  
available, have one installed by a qualified electrician. Do not cut off the grounding pin in order  
to make the plug fit into an inappropriate power outlet.  
7. For 230VAC operation, a power cord with tandem blade plug is required. Select your power  
cord in accordance with the safety regulations of your country. For example  
North America  
Germany  
UL listed and CSA certified  
VDE certified  
Nordic Countries SEMKO, NEMKO, DEMKO, or FIMKO certified  
8. Do not attempt to service this product yourself! Opening or removing covers may expose  
you to dangerous voltage points or other risks. Refer all servicing to qualified service  
personnel.  
9. The plug on the power cord is intended to serve as the disconnect device. The socket-outlet  
should be installed near the equipment and should be easily accessible.  
Notice : Actual safety specifications please refer to the label on the back of monitor.  
4
 
PR711FL User’s Manual  
Recommendation for Optimum Performance  
Your monitor will provide the best results if you follow these recommendations:  
1. Do not use your monitor against a bright background or where sunlight or other light sources  
will shine directly on the screen.  
2. Place the monitor just below eye level (10° -15°) for optimum viewing.  
3. Set the monitor brightness level to match the ambient room light.  
4. For optimum focus, the contrast control should not be set to the maximum unless the input  
signal level is extremely low. Also, the brightness control should be set to a point where the  
overall background area just begins to disappear.  
CAUTION  
Do not scrap or knock the surface of CRT with a pen, a screwdriver and so on.  
Clean the CRT surface with a lint-free, nonabrasive, soft cloth, and should not  
use the solution or glass cleaner containing corpuscles like an abrasive,  
alcohol and an alkaline solution.  
5
 
PR711FL User’s Manual  
Introduction  
The monitor is a multiple frequency high-resolution color monitor for IBM compatible PC's or  
Macintosh and workstation systems. The monitor is equipped with microprocessor based  
intelligence and multiple frequency scanning capability, allowing it to provide maximum  
compatibility for various system platforms.  
The monitor uses the latest screen technology including a 0.24mm AG FD Trinitron® CRT to  
display crisp text and vivid color graphics. The full-function digital control and On-Screen  
Display (OSD) system provides easy adjustment of image geometry and color settings for  
different display modes with the precision of a fixed frequency monitor.  
The monitor also has full ergonomic features. In addition to the friendly controls and user  
comfort features, the emission level of the electric and magnetic field is kept low to meet the  
Swedish MPR II or TCO standards.  
The monitor is also equipped with energy saving functions; it is compatible with the VESA  
power saving standards.  
6
 
PR711FL User’s Manual  
Installation  
Unpacking  
Your color monitor package should contain the following items:  
Color monitor with tilt/swivel base  
(with Signal cable)  
Power cord  
User's Guide / Driver CD  
System Setup  
1. Turn off the system and all attached peripherals.  
2. Carefully turn the monitor upside down.  
7
 
PR711FL User’s Manual  
Remove the Tilt/Swivel Base  
1. Squeeze and hold the latches.  
2. Pull the tilt/swivel base to the rear of the monitor and lift to remove the base.  
Installing the Tilt/Swivel Base  
1. Align the base with the slots on the bottom of the monitor and insert the tilt/swivel base into  
the slots.  
2. Push the tilt/swivel base firmly toward the front of the monitor until the latches click into the  
locked position.  
8
 
PR711FL User’s Manual  
Controls and Adjustments  
Once installation is complete, refer to this section for useful tips on how to use your monitor  
controls and make adjustments to match your personal preferences. The following indicators,  
controls and adjustments, including On-Screen Displays (OSD), are accessible from the front  
of your monitor:  
Front Panel Controls  
1. Power Switch  
To turn the monitor on or off.  
2. Power LED Indicator  
As long as the monitor is powered, this indicator is lit. In normal operation, it lights green. While  
in power saving mode, the indicator will turn to amber.  
3. Enter " " button  
To display the OSD manual and selected function.  
9
 
PR711FL User’s Manual  
4. Up " " button  
To adjust the selected OSD function or the contrast directly.  
5. Down " " button  
To adjust the selected OSD function or the brightness directly.  
6. "ESC" button  
To close the OSD manual and to escape function.  
How to Make On-Screen Display (OSD) Adjustments  
On-Screen Displays are called up from the front panel controls as noted above. Adjustments  
are made with " " , " " , " " and "ESC" control switches.  
Power Saving Note:  
This monitor is equipped with an automatic power-saving circuitry design that will work with  
any computer, which meets the VESA DPMS standard. It meets the ENERGY STAR low  
power state definition.  
OSD (On-Screen Display) Controls  
(1) Press " " to open the On-Screen menu function. Seven adjustment functions will appear  
on the On-Screen menu.  
Press " " or " " button to scroll selections from top-down sequence as below.  
Press " " to enter the item which is selected or to activate the preferred adjustments.  
Press "ESC" to exit the On-Screen Menu or up level.  
10  
 
PR711FL User’s Manual  
A. Status  
To display existing timing data of resolution and frequency.  
B. Picture  
a. Press " " or " " to select Vertical and Horizontal  
b. Press " " to process.  
position, Vertical and Horizontal size.  
c. Press " " or " " to preferred picture.  
C. Geometry  
a. Press " " or " " to select Side-pin, Balance,  
b. Press " " to process.  
Keystone, Parallel, Rotate and Corner.  
c. Press " " or " " to preferred picture.  
11  
 
PR711FL User’s Manual  
D. Color  
a. Press " " or " " to select various white color  
b. In User item, presses " " to confirm action color  
c. Press " " or " " to select Red, Green and Blue  
d. Press " " or " " increase or decrease density.  
temperature standard.  
adjustment.  
then press "Enter" to process.  
E. Advanced  
a. Press " " or " " to select Moire, Converge or  
b. Press " " to proceed.  
Degauss.  
c. Press " " or " " to preferred picture.  
E-1. Moire  
Press " " or " " to reduce Moire.  
12  
 
PR711FL User’s Manual  
E-2. Converage  
a. Press " " or " " to select Horizontal  
b. Press " " to proceed.  
or Vertical convergence adjustment.  
Caution:  
1. If moire reduction is overdone, picture quality, i.e. focus and vertical line stability will both be  
effected.  
2. Proper adjustment is recommended for not effecting picture performance.  
F. Recall  
Press " " to confirm window.  
If this window appears, that means it cannot be preset.(factory mode only)  
13  
 
PR711FL User’s Manual  
Confirm the Recall action by pressing the " " or cancel the action by pressing the "ESC".  
G. Language  
Press " " or " " to select the Language for OSD only.  
(2) Contrast/Brightness:  
When OSD is off, " " or " " will be adjust contrast or brightness.  
14  
 
PR711FL User’s Manual  
Trouble Shooting  
Notify your supervisor or contact your service personal when:  
Power cords are frayed or damaged.  
Liquid is spilled into the monitor.  
The monitor does not operate normally when operating instructions are  
observed.  
The monitor has been dropped or the cabinet has been damaged.  
Review this list of trouble-shooting tips before contacting an authorized service center.  
Problem  
What to do  
Make sure Power control is in the ON position.  
Power Indicator (LED) is not lit.  
Check the power cable. It must be plugged in  
completely.  
If the Power Indicator is amber-colored your  
computer has sent the monitor into its Power  
Save mode (See "Energy Declaration.")  
No Picture.  
The video card may not be seated properly.  
Make sure it is fully seated in its slot.  
No Signal Input.  
Make sure the signal cable is connected  
securely to the video card or computer.  
Enable "Power Save" function.  
15  
 
PR711FL User’s Manual  
Readjust the signal based on spec. Reference  
"Scan Frequency".  
Signal Out of range.  
Refer to "Controls & Adjustments." You need to  
adjust "Size" and "Position" of the image.  
Display image is not centered or  
is too small or too large.  
Make sure the signal cable is connected  
securely to the video card or computer.  
Image is scrolling or is unstable  
Adjust Contrast and Brightness controls.  
Picture is fuzzy or color looks  
blotchy.  
On all Models select the Degauss function in the  
OSD control menu.  
(CAUTION: Allow a minimum of 20 minutes to  
elapse before depressing Degauss button again  
when not switching between modes. DO NOT  
HOLD THE BUTTON DOWN  
CONTINUOUSLY.)  
Move devices that might be causing electrical  
interference away from the monitor. (See "FCC  
Information.")  
Picture bounces or a wave  
pattern is present.  
16  
 
PR711FL User’s Manual  
Refer to "Controls and Adjustments." You need  
to adjust the "Side Pincushion."  
Edges of display are curved  
inward or outward.  
Verify that the host system is Plug & Play  
compatible.  
No Plug & Play.  
Check to see if Windows is installed, and the  
software key for the Data Display Channel  
(DDC) function is enabled.  
Determine if original manufacturer's detachable  
signal cable is being used (D-Sub-15 pin only).  
Our monitor is build-in FD Trinitron® CRT. This CRT is sensitive to shocks and vibrations that  
may occur during transportation. Following are some adjustment tips when below mentioned  
symptoms occur.  
Symptom  
Tip  
This is normal characteristic of FD Trinitron®  
CRT.  
Two horizontal lines are visible  
on the screen  
These are damper wires, which are attached to  
the aperture grille and are designed to dampen  
and prevent shock and vibrate to the aperture  
grille.  
17  
 
PR711FL User’s Manual  
Degaussing the screen.  
Black fine vertical lines are  
visible on the screen. Shock and  
vibration may cause the aperture  
grille misaligned, which results  
few fine black vertical lines  
across the screen  
Tap lightly (do not hit) the side of the monitor.  
If above mentioned remedies do not work,  
please do the following:  
1.Display full white window or wallpaper  
background over the area where the black lines  
appears.  
2.Set Contrast and Brightness to the maximum,  
wait for a moment until the problem is corrected.  
You may try to tap lightly the side of the monitor.  
18  
 
PR711FL User’s Manual  
Energy Declaration  
This monitor is equipped with a function for saving energy, which supports the VESA Display  
Power Management Signaling (DPMS) standard. This means that the monitor must be  
connected to a computer, which also supports the VESA DPMS standard to fulfill the  
requirements of the NUTEK specification 803299/94/96. The time settings for switching to a  
power saving mode are adjusted from the system unit by software. From the first indication of  
inactivity to power saving position A2 the total time must not be set to more than 70 minutes.  
1. VESA Power-Management Proposal  
H. sync  
Off  
V. sync  
On  
Video  
Blank  
Blank  
Blank  
State  
Stand-by  
Suspend  
Off  
On  
Off  
Off  
Off  
2. Power Consumption (120/230 Vac)  
Power  
NUTEK  
VESA state  
On  
LED indicator  
Green  
Consumption  
< 100W  
< 15W  
Normal operation  
Power Saving  
Position A1  
Suspend  
Amber  
Power Saving  
Position A2  
Off  
Amber  
< 5W  
* Recovery Time < 3 Sec.  
19  
 
PR711FL User’s Manual  
Specification  
43.1 cm / 17" (16" viewable screen size)  
Color Picture Tube  
diagonal measurement, 90 degree deflection,  
FD Trinitron® CRT, anti-glare, anti-reflection,  
anti-static, medium short persistence phosphor,  
dark bulb  
0.24 mm, (at center)  
AG Pitch  
Analog 0.7V peak to peak separate TTL  
Positive or Negative  
Input Signal  
Horizontal: 30 to 97 kHz automatically  
Vertical: 50 to 160 Hz automatically  
Scan Frequency  
1600 x 1200 pixel, non-interlaced  
Analog input, unlimited colors  
202 MHz  
Max. Resolution  
Display Colors  
Pixel Rate  
DDC 1 / DDC 2B  
Plug & Play  
100-240 VAC, 50/60 Hz (automatically)  
100W max.  
Power Supply  
Power Consumption  
Dimensions  
412(W) x 415(H) x 430.5(D) mm  
20.1 kgs(G.W.), 17.6kgs(N.W.)  
Weight  
Operating Temperature: 0°C to 35°C  
Humidity: 20% to 80%  
Environment Consideration  
Storage Temperature: 0°C to 60°C  
Humidity: 10% to 90%  
Note: Specifications are subject to change without notice.  
20  
 
PR711FL User’s Manual  
Reference Information  
This color monitor supports multiple operating platforms such as IBM compatible and  
Macintosh family computers. This section provides you with detailed information on pin  
assignment of the D-Sub connector and the preset timing chart of the prevailing video  
standards.  
Connector Pin Assignments  
Male Mini D-15 Connector  
Signal  
Red Video  
15 Pin Mini D-Sub  
1
Green Video  
Blue Video  
Horizontal Sync  
Vertical Sync  
Ground  
2
3
13  
14  
4,6,7,8,10,11  
No Connection  
SDA (DDC)  
SCL (DDC)  
5,9  
12  
15  
21  
 
PR711FL User’s Manual  
Preset Timing Chart  
Note: This monitor is equipped with a microprocessor which allows the user to set his own  
preferred mode(s) beyond those standard mode listed below.  
To reduce visual tiredness and eyestrain, it is recommended to choose the highest refresh  
modes available.  
Horizontal  
Resolution  
Format  
Refresh Rate (Hz)  
Frequency (KHz)  
640x480@60Hz  
720x400@70Hz  
800x600@75Hz  
800x600@85Hz  
832x624@75Hz  
1024x768@75Hz  
1024x768@85Hz  
1152x864@75Hz  
1280x1024@75Hz  
1280x1024@85Hz  
VGA  
VGA  
31.5  
31.5  
46.9  
53.7  
49.7  
60  
60  
70  
75  
85  
75  
75  
85  
75  
75  
85  
VESA  
VESA  
MAC  
VESA  
VESA  
MAC  
68.7  
67.5  
80  
VESA  
VESA  
91.1  
22  
 

CNET Network Router CBR 980 User Manual
COBY electronic TV Cables HDMI 12 User Manual
Cooper Lighting Work Light SC1000R User Manual
Craftsman Snow Blower 24788664 User Manual
Danby Refrigerator DWC283BLS User Manual
Dixon Lawn Mower SE 5225 KOH CE User Manual
Dynex Camera Accessories DX DA101381 User Manual
Edelbrock Automobile Parts Carburetor User Manual
Electro Voice Microphone CT30 User Manual
Electro Voice Speaker System FRX+640 User Manual