Milwaukee Drill 54 06 2800 User Manual

BULLETIN NO.  
54-06-2800  
SERVICE PARTS LIST  
REVISED BULLETIN  
DATE  
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS  
Jan. 2003  
1/4 INCH DRILL  
WIRING INSTRUCTION  
STARTING  
ATALOG NO.  
058A  
58-01-1805  
0100-20  
SERIAL NO.  
36  
37  
38  
39  
40  
41  
42  
43  
Slug  
Slug  
Brush Spring  
Brush Assembly  
3/8-16 x 5-1/2 Hex Cap screw  
SideHandleClamp  
SideHandle  
Q.  
45-30-0030  
45-30-0035  
23-52-1610  
22-18-1310  
06-75-2850  
42-68-0800  
43-62-0845  
06-54-0325  
(2)  
(1)  
(2)  
(2)  
(1)  
(1)  
(1)  
(1)  
FIG.  
1
2
3
4
5
6
7
8
PART NO.  
02-04-0640  
02-04-0645  
02-04-0852  
02-04-1229  
02-50-1611  
02-50-2400  
06-82-7275  
12-99-2565  
16-10-2215  
18-07-2200  
22-18-1210  
22-56-1010  
48-76-4008  
23-66-2585  
28-14-2390  
28-28-2320  
31-15-2030  
31-50-2040  
32-40-0100  
32-75-0115  
34-80-2300  
36-66-0125  
38-50-5750  
42-14-0460  
43-44-0985  
44-60-1700  
45-04-0750  
45-36-1095  
45-88-7990  
DESCRIPTIONOFPART  
Ball Bearing  
Ball Bearing  
Ball Bearing  
Ball Bearing  
Needle Bearing  
Needle Bearing  
7-18 x 3/4 Slotted Plastite T-20  
Service Nameplate  
Armature  
NO.REQ.  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(6)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
3/8-16 Square Nut  
LUBRICATION (Type "Y" Grease, No. 49-08-5270)  
• Place 5 gm. (.02 oz.) of grease on top of the inserted intermediate  
ball bearing (1) and on the intermediate pinion (22).  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
29  
30  
Field  
Brush Card Assembly  
Pin Housing Assembly  
Quik-Lok Cord Set  
Switch  
Gearcase  
Diaphragm  
Handle Halve  
Motor Housing  
Intermediate Gear  
Spindle Gear  
RetainingRing  
Intermediate Shaft  
Spindle  
Baffle Assembly  
Gasket  
Ground Pin  
• After inserting all gearing, place 13 gm. (.46 oz.) of grease at the  
armature pinion location in the gearcase (15) and fill to the top of  
the intermediate gear (19). Grease must contact at least 25% of  
the intermediate gear teeth.  
Before assembly, lightly coat all press fit areas with  
lightweight spindle oil.  
FIG.  
4,20  
NOTES:  
Support the output ball bearing inside the gearcase before  
pressing off the spindle gear.  
5,6  
Needle bearings to be pressed flush to .010 under flush  
from the end which has the vendors identification.  
Chuck Screw  
Spindle Spacer  
Thrust Washer  
MILWAUKEEELECTRICTOOLCORPORATION  
13135 W. LISBON RD., BROOKFIELD, WI 53005  
Drwg. 3  
 

NEC Telephone DTerm Series E Telephones User Manual
NEC TV Cables E323 User Manual
NeumannBerlin Microphone Condenser Microohone User Manual
Nokia Cable Box CA 55 User Manual
Northern Industrial Tools Grinder 157791 User Manual
Nuvo Stereo Amplifier LSA40 User Manual
Olympus Computer Drive C P20U User Manual
Omega Power Supply DRN PS 1000 User Manual
Oregon MP3 Player MP 130 User Manual
Paradyne Network Card TAM1500 12 User Manual